<<  
crownxls2000-071010

XLS DRIVECORE 2000

S CR719

CROWN

Minimum Guaranteed Power
per channel, both channels driven
  XLS 1000
 XLS 1500
 XLS 2000
 XLS 2500
Stereo, 2 ohms (per ch.) 550W 775W 1050W 1550W
Stereo, 4 ohms (per ch.) 350W 525W 650W 775W
Stereo, 8 ohms (per ch.) 215W 300W 375W 440W
Bridge-Mono, 8 ohms 700W 1050W 1300W 1550W
Bridge-Mono, 4 ohms 1100W 1550W 2100W 2400W

Crown's XLS Series amplifiers define the standard for portable PA systems with unmatched performance, technology and affordability. Its advantageous flexibility includes multiple inputs so you can plug in anything and play anywhere, along with several system setup configurations. The integrated crossovers and switch-mode power supply produce superior sound, and Peakx™ limiters protect your speakers. Weighing less than 12 pounds, compared to 40 pounds for its competitors, it's much easier to set up and move from show to show. Simply put, the XLS is most reliable, versatile, efficient amp available today.

XLS

  • XLS High Performance, Lightweight Class D amp weighs less than 11 lbs.
  • Integrated PureBand™ Crossover System for better performance and control
  • Peakx™ Limiters provide maximum output while protecting your speakers
  • XLR, 1/4", RCA inputs provide outstanding flexibility
  • Efficient forced-air fans prevent excessive thermal buildup
  • Electronically balanced XLR inputs; touchproof binding post and Speakon® outputs
  • Precision detented level controls, power switch, power LED, and six LEDs which indicate signal, clip and fault for each channel
  • Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications

Specifications

Sensitivity (for full rated power at 4 ohms)

1.4 Vrms

Frequency Response (at 1 watt, 20 Hz - 20 kHz)

+0 dB, –1 dB

Signal-to-Noise Ratio

Rated as dBr to full rated 8Ω power output (A-Weighted):
XLS1000 > 97 dB
XLS1500, XLS2000, XLS2500 > 103 dB

Damping Factor (8 ohm): 10 Hz to 400 Hz

> 200

Crosstalk (below rated 8Ω power)

At 1kHz: > 85dB
At 20kHz: >55dB

Input Impedance (nominal)

20 kΩ balanced, 10 kΩ unbalanced

Load Impedance

2 to 8 Ω per channel in Stereo
4 to 8 Ω in Bridge Mono

AC Line Voltage and Frequency Configurations Available (± 10%)

120 VAC 60 Hz
100 VAC 50/60 Hz
220 and 240 VAC 50 Hz

Ventilation

Flow-through ventilation from front to back

Cooling

Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation

Air Volume Requirements (per minute per unit)

80.15 ft³ (2.27 m³)

Integrated Processing

PureBand™ Crossover System

Crossover Filter: Linkwitz-Riley 24dB per Octave

Crossover Frequency Range: 50 HZ - 3 kHz

Crossover Mode: Crossover (CH1=LPF, CH2=HPF), LowPass (both channels LPF), HighPass (both channels HPF), Bridge (LPF or HPF).

Peakx™ limiters: Channel independent clip limiter designed to
provide maximum output while protecting your loudspeakers

Input/Output

Input Connectors: XLR (one per channel), 1/4-Inch (one per channel), and RCA (one per channel). 1/4-Inch connectors can be used as loop-thrus to distribute signal to additional amplifiers.

Output Connectors: Two 4-Pole Speakon® Output Connectors
accept 2-pole or 4-pole Speakon® connectors. The top Speakon connector is wired for both channels so it can be used for bridgemono wiring or for stereo wiring of two speakers to a single Speakon connector.

One pair of back-panel binding posts per channel; accepts
banana plugs or bare wire. (European models do not accept
banana plugs.)

Construction

XLS1000/XLS1500: 8.12-Inch (20.62cm) depth
XLS2000/XLS2500: 10.35-Inch (26.29cm) depth

Dimensions

EIA Standard 19-inch (48.3-cm) rack mount width
(EIA RS-310-B), 3.5-inch (8.9-cm) height.
XLS 1000/1500: 7.7-inch (19.6-cm) depth.
XLS 2000/2500: 10.7-inch (27.2-cm) depth.

Net Weight , Shipping Weight

XLS1000: 8.6 lb (3.9kg), 13.6 lb (6.2 kg)
XLS1500: 8.6 lb (3.9kg), 13.6 lb (6.2 kg)
XLS2000: 10.75 lb (4.9kg), 15.8 lb (7.1 kg)
XLS2500: 10.75 lb (4.9kg), 15.8 lb (7.1 kg)

!
 <<  
+Shipping charges